What is the strength of high-strength bolts?
Release time:
2023-04-17
source:
network
High Strength Friction Grip Bolt, also known as HSFG. It can be seen that the high-strength bolts we refer to in Chinese construction are the abbreviation for high-strength friction pre tensioned bolts. In daily communication, simply abbreviating the words "friction" and "Grip" has caused many engineering and technical personnel to misunderstand the basic definition of high-strength bolts.
What is a high-strength bolt?
High Strength Friction Grip Bolt, also known as HSFG. It can be seen that the high-strength bolts we refer to in Chinese construction are the abbreviation for high-strength friction pre tensioned bolts. In daily communication, simply abbreviating the words "friction" and "Grip" has caused many engineering and technical personnel to misunderstand the basic definition of high-strength bolts.
Myth 1:
Is a bolt with a material grade exceeding 8.8 a "high-strength bolt"?
The core difference between high-strength bolts and ordinary bolts is not the strength of the materials used, but the form of force applied. The essence is whether to apply preload and use static friction to resist shear.
In fact, in the British standard specifications, the American standard specifications only mention two types of high-strength bolts (HSFG BOLT): grade 8.8 and grade 10.9 (BS EN 14399/ASTM-A325&ASTM-490), while ordinary bolts include 4.6, 5.6, 8.8, 10.9, 12.9, etc. (Table 2 of BS 3692 Clause 11); It can be seen that the strength of the material is not the key to distinguishing high-strength bolts from ordinary bolts.
What is the strength of high-strength bolts?
According to GB50017, calculate the tensile and shear strength of individual ordinary bolts (Class B) with grade 8.8 and high-strength bolts with grade 8.8.
Through calculation, we can see that under the same grade, the design values of tensile strength and shear strength of ordinary bolts are higher than those of high-strength bolts.
So where is the strength of high-strength bolts?
To answer this question, it is necessary to start with the design working states of the two types of bolts, study their elastic-plastic deformation laws, and understand the limit state at the time of design failure.
Ultimate state at design failure
Ordinary bolt: The screw itself undergoes plastic deformation that exceeds the design tolerance, resulting in the screw being sheared out.
Ordinary bolt connections will experience relative slip between the connecting plates before bearing shear force, and then the bolt rod and the connecting plate come into contact, causing elastic-plastic deformation and bearing shear force.
High strength bolts: The static friction force between the effective friction surfaces is overcome, and the two steel plates undergo relative displacement, which is considered failure in design considerations.
In high-strength bolt connections, the friction force first bears the shear force. When the load increases to a point where the friction force is insufficient to resist the shear force, the static friction force is overcome, and the connecting plate undergoes relative sliding (ultimate state). But although it is damaged at this time, the bolt rod can still use its own elastic-plastic deformation to withstand shear force when in contact with the connecting plate.
Mistake 2:
Is high load-bearing capacity a high-strength bolt?
From the calculation of a single bolt, it can be seen that the design strength of high-strength bolts in terms of tensile and shear strength is lower than that of ordinary bolts. The essence of its high strength is that during normal operation, nodes are not allowed to experience any relative slip, that is, small elastic-plastic deformation and high node stiffness.
It can be seen that under a given design node load, nodes designed with high-strength bolts may not necessarily save on the number of bolts used, but their deformation is small, stiffness is large, and * * reserves are high. High strength bolts are suitable for use in main beams, and other locations that require high node stiffness, in accordance with the basic seismic design principle of "strong nodes, weak members".
The strength of high-strength bolts is not due to their designed load-bearing capacity, but rather to the high stiffness, high performance, and strong resistance to failure of the design nodes.
News
The company mainly produces standard parts, high-strength steel structures, high-strength bolts specially used for wind power, double-headed high-pressure bolts, nuts, machining of mechanical parts and riveting weldments, etc. It produces supporting parts for some large and medium-sized companies in the province and other places, and high-strength bolts specially used for wind power and thermal power companies.
Contact Us
Add:Chaoyang Village, Chaoyang Town, Mengjin County, Luoyang City, Henan Province
Tel:+86 15837939996